Get Our Email Letter

Subscribe to the Original Artesano mailing list to receive updates on new arrivals, special offers and other discount information.

Toggle Nav

Cement Tile Installation Guide


Cement tiles originate from Spain and Southern France during the 19th century. Cement tiles are handcrafted by pressing support on to hydraulic presses using steel molds and brass dividers for each special design.

100% non-burn making process, ecofriendly and unique artisan process. Each cement tile is individually handmade and varies in thickness, size and color. Imperfection such as irregular edges, as well as pattern contours being partly blurred are inherent to the manufacturing process. These characteristics contribute to the essential tile’s nature appeal without compromising its performance.

Our tiles are sealed to protect them from dirt and water, with our solvent-based sealer. If you require for your order of tiles to be kept at raw for later sealer application at job site, please specify us in your order.



The tiling substrate must be prepared in accordance with design, lower than the tiled platform from 25-30mm.The tiling substrate must be flat stability, clean and a bit wet.

If you are laying tile on a concrete slab, be sure the slab is completely cured to prevent white efflorescence spots from showing up later on the surface of the tile as water evaporates through it. Also do not use a rubber hammer nor normal hammer, use your hand to push and install tiles.


Soak tiles in water at least 10 minutes to remove any dust and in order to pre-wet the back side prior setting. Since the tiles are handmade and therefore tiles’ color variation may happen, we recommend that you mix them randomly from different boxes when laying them out in order to balance color and tonal variation. If you are installing a sub-floor heating system: do not under any circumstance allow the system to be powered on until the installation is complete.

Use a ruler and tapeline to locate the construction area. From a fixed line and corner, start to install based on the selected design. The pattern tile looks best with small grout joints (from 1 to 3 mm).

Keep installing on follow stretched parallel lines and cords to determine the tiled surface.

Install each row until you finish construction area. When installing press the tiles down firmly into place only by hand – please don’t use a hammer or mallet since the cracks may show up later, even if you do not see them immediately. Working in small areas at a time and avoid getting the thin-set on the surface of tile – please wipe off any excess thin-set or other dirt immediately so as to avoid it setting in the porous surface.

After finish placing the tile on the substrate, spray clean water on the surface to enhance adhesion between tiles and substrate.

STEP 3 Sealing:

Our standard tiles are pre-sealed, which you don’t need to do sealing again in work. However, with some customs order, the tiles are requested to keep it raw. Therefore, please note that sealing has to be performed before grouting, otherwise, grout can penetrate the porous surface of the tiles. If you want to do the sealing one more time, please use only the solvent-based sealer, which it will be completely matched with our pre-treat sealer.

STEP 4 Grouting:

Before grouting tiles should be allowed to dry for at least 24 hours, recommend 3 days after fixing. We request not using dark colored grout with pale tiles and vice versa. Use un-tinted grout only, or closely-match the grout on solid color tiles. Improper installation can cause the tiles to be stained by the grout tint, causing haze over dark regions, or making lighter regions appear dingy.

Do not use any oils or cleaning chemicals to apply to the tile face.

Apply the grout just enough in the area around of tile join only. Please don’t put the grout and flat over the whole tile’s surface. Always moving diagonally across the joints. Any excess grout should be removed with a damp cloth or sponge before it dries

STEP 5 Maintenance:

The tile should be cleaned using mild soap, but not by detergent. Never use acidic cleaner or other acids on cement tile. Depending on the amount of foot traffic the tiles will have to be re-sealed periodically with a suitable sealer. The tiles are not recommended to install outdoors but possible to use with special consideration and application of extra sealer, heat and sun light condition.

COMPLAINTS AND CLAIM Please inspect your tiles prior the installation work carried out. No returns or claims will be accepted once the tiles have been installed. We will do not assume any responsibility for faulty workmanship installation.